Dipping Display Merchandiser HF040WWG/0LCG


HF model dipping-display ice cream cabinets feature standard lid, low profile flat glass lid and low profile curved glass lid models to suit most any ice cream merchandising need. Each model features a full glass top and LED lighting to maximize product visibility. HF model ice cream cabinets are designed for operator comfort with a curved rear edge and a lowered back wall which makes it easier to reach inside the case and scoop ice cream. The cold wall evaporator design provides even temperature throughout the cabinet to ensure ice cream quality.

Standard Features

  • Eco-friendly R290 refrigerant
  • Independent on/off light switch to save energy when not in use
  • Electronic controller system that decreases service call time and saves energy by maintaining consistent product temperature
  • 2-1/2” thick polyurethane foamed-in-place walls for maximum insulation and performance
  • Drain with garden hose connector for ease of cleaning
  • Heavy-duty epoxy-coated wire can support racks
  • Side compartment grille in addition to back access improves refrigeration system performance and accessibility during routine servicing

HF040WWG/0LCG Low Curved Glass Dipping Display Merchandiser


  • Rounded rear stainless steel heated top improves operator comfort
  • Lower back rail provides improved operator ergonomics
  • Frameless double pane tempered glass viewing window, with NSF51 approved powder coated top and bottom aluminum extruded trims, provides enhanced structural stability and appearance
  • Tempered glass ends improve product visibility
  • Energy efficient, long lasting LED lighting
  • Independent on/off light switch
  • Standard electronic controller increases reliability and saves energy by maintaining consistent product temperature
  • 24 gauge painted textured interior and exterior
  • Stainless steel top and attached superstructure
  • Stainless steel serving deck
  • Equipped with leveling legs to correct for unlevel flooring situations
  • Drain with garden hose connector for ease of cleaning
  • Heavy-duty epoxy-coated wire can support racks
  • 3″ thick walls and 2-1/2″ floor with foamed-in-place “zero ODP” urethane insulation
  • Hinged, high-tensile, transparent acrylic dipping compartment lids with full length handle
  • Eco-friendly R290 refrigerant
  • Cold wall evaporator
  • Low maintenance condenser coil
  • Condenser filter screen, removable without tools, for easy condenser coil cleaning resulting in peak efficiency and extended equipment life (HF160 and HF230 models). Screen should be cleaned every three months depending on operating environment.
  • Rear air intake with side and rear discharge eliminates front grille and allows full front of cabinet for graphics
  • Side compartment grille improves the air circulation and accessibility during servicing
  • No minimum clearance required on cabinet sides but front, back and top must be left open for customer and operator access
  • Temperature range: 5° to -5°F (-15° to -21°C)
  • R-factor (insulation efficiency rating): 19.40
  • UL and C-UL listed and UL EPH classified.
  • Warranty: Standard limited two year parts and labor with additional three year coverage on compressor part


  • Crated Weight (lbs)(kg):264 (120)
  • Crated Height (in)(cm):60 (150)
  • Crated Width (in)(cm):45 (113)
  • Crated Depth (in)(cm):40 (100)
  • Interior Display Height (in)(cm):20 (51)
  • Interior Display Width (in)(cm):21 (53)
  • Interior Depth (in)(cm):21-1/2 (55)
  • Can Capacity Display:4 **
  • Can Capacity Storage:0
  • Overall Height (in)(cm):50 (127)
  • Overall Width (in)(cm):27-1/4 (69)
  • Overall Depth (in)(cm):27-1/2 (70)
  • Condensing Unit Size:3/5 HP
  • Refrigerant:R290
  • Electrical Characteristics:115/60/1
  • Cord and Plug Furnished:Yes
  • NEMA Plug Configuration:5-15P
  • Total Amp Draw:5.9
** Capacities in 9-1/2″ diameter, 3 gallon cans

Optional Features

  • Custom colors
  • Removable can holders with white overnight can covers
  • Dipper well
  • Removable frost shields
  • Leg kit
  • Casters
  • Flavor identification tabs (standard lid models only)
  • Lid locking kit (less locks, requires one kit per lid)